abumazen, What have you tried so far to recover your player?
What is happening with it at the moment?
When did the problem start?

Re: DEAD PLAYER RECOVERY GUIDE
 

Hi Guys,
I got this cool product UX-Osmium from Uxcell (got it about 5 days ago). It was working fine untill 2 days ago it suddenly restarted while I was listening to music. Now it is stuck at the Hour Glass Icon when it loads. I tried to connect it to my pc that it had worked before and it got detected as a new device called USB 2.0 (HS) ADFU Device. And there was no drive assigned to it. I tried the software that came with it, no luck. Can't even format it as there is no drive associated.

Uxcell shipped it on 27th of Nov, so I don't think I can return it as it says on thier site that only 14 days after shipping I can return it.

I tried upgrading the firmware but I get the following error message.

http://new.photos.yahoo.com/war1000/...804098058064/1

Any help is highly appreciated. I contacted Uxcell but in two days no response.

war1000, It seems your player has gone into recovery mode, you would need a copy of the original factory Full version firmware to recover it. Get on to UXcell as soon as possible for a replacement and do not try to load any furthur firmware as you will void your warrenty.

That work but, i have just 228MB capacity/ 4G. I dont understand.

lefrosth, These players are not able to support 4GB of memory 2GB is the maximum. I went back through your posts and see you listed your memory chip serial number as K9K8G08U0M.
On Samsung chips the 4 & 5th characters represent the chip density in your case 8G which is 8gigabit or 1GigaByte.
If your player is only showing 228MB then one of the following may have happened.
The chip has been marked as a 1GB chip but is really only 256MB.
The serial number has been misread and is actually K9K2G08U0M which is a 256MB chip.
The chip is in fact a 1GB but has failed in some way and not all the memory is accessible.
When you used the MP3 Disk Tool to rebuild the partition the slider was not set all the way to the left at zero before you repartitioned in which case you may be able to repeat the process and restore the chip to 1GB.

This is why you were having problems with file corruption because the files were being loaded to damaged sectors or space that did not really exist.

Here is a post regarding a 4GB player I purchased that was in fact a 2GB chip.
http://www.mympxplayer.org/hotmale16...nz-vt2786.html

I have always this problem i have just 228mb it wird :S i m very bad looky ...

http://awdclub.no-ip.org:8080/frosth/mp4/228.gif

I START TO UPDATE MY MP4 WITHOUT MAKE A BACK UP OF THE ORIGINAL FIRMWARE (NOW THE SCREEN IS DARK BLUE). MY TROUBLE IS KNOW THE RIGHT FIRMWARE FOR MY MP4.

THE SPECIFICATIONS OF THE MP4 ARE THESE:

MEMORY: samsung 637 K9F4G08U0A PCB0

BOARD: MP-693C-SL KEY V1.2 KNIFE 051111

CPU:ATJ2085H

4 GB

COLOR:BLACK LIKE IPOD NANO

I HAVE DAYS SEACHING IT!!

GIVE ME SOME OPTIONS TO CHOOSE
(IF I HAVE MORE THAN ONE FIRMWARE THAT CAN WORK PLEASE TELL ME)

lefrosth, Go into the player settings menu and select Online Mode and set it to Multi Drive.
Then disconnect your player from your PC turn it off at the switch. Turn it back on and reconnect it to your PC. How many Drives does it now show in Explorer 1 or 2.

just one

now i dont have a problem with files,but 228mb it is very smallest loll...

lefrosth, If that is the case I doubt you will be able to recover the memory either because part of the chip has failed or it is an incorrectly labeled 256MB chip.

The only other thing I can think of and it is just a guess is that the firmware you used to recover your player has put some limitation on the chip.

When you first tried upgrading the firmware did you do so because you where you having problems with the player?

abumazen do you have more information on your MP3? What is your ship? ... Do you have a pic? Do you want a firmware?))))


my friend lefrosth,,

my player is white one G 1.5 style sony mp4 player

this is a picture of a mp4 like my player

http://www.mympxplayer.org/image-asp205.html

and i want the compatible firm ware for it

(((((abumazen, What have you tried so far to recover your player?
What is happening with it at the moment?
When did the problem start?
)))))

tedad 1 the problem started a week ago when I tried TO UPDATE MY MP4 WITHOUT MAKE A BACK UP OF THE ORIGINAL FIRMWARE (NOW THE SCREEN IS DARK BLUE). MY TROUBLE IS KNOW THE RIGHT FIRMWARE FOR MY MP4

i tried some firmwares but no good result

my vesion again is:

sc8505 1f

25/4/2006

act_v3.5.35

1.5 inch

1 G

sony player

please help me

Yes but, i have buy 3 MP4 similar on ebay the same seller. I m only just have this problem ...

abumazen, Have you tried these with link form tadad1.With me that work
http://www.mympxplayer.org/some-9048...ds-vt2895.html

lefrosths

i tried it but does not work

i told you that the version is 3.5.35

made also in china

if you find a chinese 3.5. 35 firmware please send me it

Guys, do you know how long it takes Uxcell to respond? its been 3 days and I sent them 2 emails, no response yet.

Thanks.

I START TO UPDATE MY MP4 WITHOUT MAKE A BACK UP OF THE ORIGINAL FIRMWARE (NOW THE SCREEN IS DARK BLUE). MY TROUBLE IS KNOW THE RIGHT FIRMWARE FOR MY MP4.

THE SPECIFICATIONS OF THE MP4 ARE THESE:

MEMORY: samsung 637 K9F4G08U0A PCB0

BOARD: MP-693C-SL KEY V1.2 KNIFE 051111

CPU:ATJ2085H

4 GB

COLOR:BLACK LIKE IPOD NANO

I HAVE DAYS SEACHING IT!!

GIVE ME SOME OPTIONS TO CHOOSE
(IF I HAVE MORE THAN ONE FIRMWARE THAT CAN WORK PLEASE TELL ME)

Re: DEAD PLAYER RECOVERY GUIDE
 

Hello to everybody.
I'm trying to find the right firmware for my Mp3/Mp4 player, a black Nano clone. I was able to make it readable by my pc as a usb disk, but the display is still white.

HERE SOME SPECIFICATIONS:
Memory chip: SAMSUNG 622 - K9K8G08U0A 1GB
Processor: ATJ2085H
MAINBOARD: MP-752C-SL MAIN KNIFE 051207
DISPLAY: FPC-VP6620-01A_56 2006-04-04


Here some pictures of the player and the menus as before.
I hope someone could help me, telling me which firmware to load.
Thank you very much, and great job with this forum!

http://www.webalice.it/nveronesi/MP4/cover.jpg


http://www.webalice.it/nveronesi/MP4/pcb.jpg


http://www.webalice.it/nveronesi/MP4/front.jpg

http://www.webalice.it/nveronesi/MP4...ipod_clone.jpg

Re: DEAD PLAYER RECOVERY GUIDE
 

Hi there,
I have MP4 S1MP3 player with signature on the main board: "wp-693c-sl main v1.3 2005.12.14", 512MB, no FM. I tried to update the firmware but with wrong one :cry: . The player was totaly dead but i read some postes in this forum and it's now alive BUT without ebook and games :roll: . Can anyone help me how to activate them :wink: and where to find more games for it :D

Please e-mail me or write to me on ICQ 112705619 for some solutions :roll:

Re: DEAD PLAYER RECOVERY GUIDE
 

Hi
I've got the same player
Here the dump of the flash (s1fwx): http://rapidshare.com/files/9122822/dump.zip.html

I never tryed to upload it (my player works fine). Please let me know if it works

Re: DEAD PLAYER RECOVERY GUIDE
 

Hello tadat1.I cant find anywhere the firmware for my mp4 player. :!:
http://www.mympxplayer.org/viewtopic.php?p=16651#16651

Samsung 622
K9K8G08U0A
PCB0

ATJ2085H :
F521 5AB C5R


PLZZ HELP MEEEE
@___- @ @@@@ @ ______ @ @@
@____@ @______ @______ @___ @
@@@@ @@@__ @______ @___ @
@____@ @______ @______ @@@
@____@ @@@@ @@@@_@
_______________________@

Re: DEAD PLAYER RECOVERY GUIDE
 

Hi all, i have a black mp4/3 1GB player with a 1.5 inch screen slim line, it was bought for me in hong kong, i totally stuffed it up , i have used the recovery up to the blue screen part, my problems is i can find the firm ware for the player.
it has
ATJ2085H
HYNIC M7SA2044y
THESE are the numbers off the chips.
any help would be great thanks.
now it says the drive is write protected, i have tried all versions of test disk they didn't work, i am about ready to throw it away.

Re: DEAD PLAYER RECOVERY GUIDE
 

Hi Piper7,
THANK YOU VERY MUCH for your help!
You saved my friend's player! It worked at the first time! :D

PS you have 1 PM!
Thanks again!

Re: DEAD PLAYER RECOVERY GUIDE
 

I'm very happy for you :D

Some information about the firm:

Version
ACTS16D_37
2006/04/14

3.5.37-001
2006/04/14

Largest bitmaps images inside the firm are 128x160 (1'8'')
Firm has NO file browser function :(

May be a moderator want upload this firm in download area? (I think we lost it with rapidshare)

thank youuuuuuuuuuuu
you just save my player life...:)

Where can i find a internet page with all firmwares of all S1 mp4 players ???

Hello tadad1 everybody say that you kan save players..

My player is half-dead.The screen is blue, but i can hear music with it.Can you take time and help me with my plyer??
that is my player.
http://foto.mail.ru/list/sanja90/Jaw...osatru/66.html

and this is my player info:
http://www.mympxplayer.org/who-has-t...er-vt3136.html
PLZZZZ

Re: DEAD PLAYER RECOVERY GUIDE
 

I think you have to find a firmware that work with your display! I was able to hear music with dead display too, the problem is the firmware not compiled for your type of display!

Have you tried all the firmwares posted in the forum?

Re: DEAD PLAYER RECOVERY GUIDE
 

my player is look like this

http://www.mympxplayer.org/image-asp40.html

but inside this not look like ur guide

how i do ?????


sorry 4 my english

my player is dead 'cause
i update wrong firmware

i have my original firmware
but i can't turn on my mp4
& when i link to pc
it's not run

how to fix that ???

plzzzzzz tell me

plz help for dead player..i did all of the dead player guide but at the recovering position i had some problem.mp4 player cant be recovered.my player has difference from the pic in guide so it has a speaker at the backside.it is ATJ2093H and which utility must i use to recover it???sorry my english

and i wanna ask a guestion: there are two types of versions one of them like this 3.5.57 and other is like 9.0.48 what is the differences between them?

musty42, the 3.5.XX series firmwares are used on players using the ATJ2051 and ATJ2085 chips. The 9.0.XX series firmware will only work on players using the ATJ2091, 2095, 2097 and CTW500 chips.
the two are very different and you can not swap between versions.

i tried all of the versions but it doesnt work???
 

i upgraded my player with wrong firmvare it is out of order now it has black screen with light i am tring to upgrade new version but it is same no working.what must i do?
its properties:
ATJ2093H
it was working with 9.0.48
but i tried 9.0.48 versionS but i have no result

WHAT MUST I DO?PLEASE HELP....
THANKS MUCH

Re: DEAD PLAYER RECOVERY GUIDE
 

I,ve follow your guide, Tadad1, but i Have a problem.
When i install a new driver by the proprieties of USB device, after show all device, there is a window that ask me the tipe of device, and only when i click next, I can select the Driver on Windows directory. The problem is that if I select a device, the driver non work. A window tell me "The specified position doesn't contain information on the hardware".
What can I do?
Your Guide is thery beatiful, but i cannot go forward.
Thank's

Re: DEAD PLAYER RECOVERY GUIDE
 

Great guide, very detailed, its just i cant perform any of it,i have opened the player up connected and connected it to my computer, i have connected a pair of tweasers to the pins on the side of the chip endlessly for the past 2 hours and nothing has happened.

I got this problem 2 days ago when i connected it to my computer, it just swiched its self off and will not turn back on again, i have tried charging it, but nothing, so i tried this, i dont know if the battery is dead or it just isnt working because i updated it.

All i know is it is one of the nano copies from china and the chip says samsung on it.
Thanks for your help.

buckers, If the player is showing no signs of life at all when you short the chip then the problem may be hardware related. If this is the case then you may not be able to recover your player.

Re: DEAD PLAYER RECOVERY GUIDE
 

Ok, thanks anyway

hi everyone... okay here's my prob. my idiot brother messed not only with my computer but with my mp4 player as well.. he decided to upgrade it, but instead of doing it, he downgraded it.. the original version of my player was 9.0.5 and now its 3.5.35...
i tried all of the steps, and i am now stuck in the recovery process.. does it take a really really long time to recover??? should i try another program for recovery? what program would you recommend?


(by the way, i wasn't able to back up my original firmware,yup like my problem isn't big enough)