MyMPx.org
Page 26 of 28 « First 16232425 26 2728
Show 40 post(s) from this thread on one page

MyMPx.org (http://mympx.org/forum/)
-   Dead Players (http://mympx.org/forum/dead-players/)
-   -   DEAD PLAYER RECOVERY GUIDE (http://mympx.org/forum/dead-players/33350-dead-player-recovery-guide.html)

vince 5th Nov 2008 2:24 am
sir can you help me,, i have ipod 1gb cannot power on, but can charge..

sharma2862 9th Nov 2008 6:10 am
Re: DEAD PLAYER RECOVERY GUIDE
 
hi
i did the process as mentioned here and i successfully did evrything upto the final recovery process.
now my computer can read my player,i can put songs/data in it evrything ok.

but i cannot see the screen.
the screen is blank

please help?

Th3_uN1Qu3 9th Nov 2008 10:22 am
Quote:
Originally Posted by sharma2862";p=&quot (Post 53891)
hi
i did the process as mentioned here and i successfully did evrything upto the final recovery process.
now my computer can read my player,i can put songs/data in it evrything ok.

but i cannot see the screen.
the screen is blank

please help?
Bad display driver, aka wrong firmware. Keep trying...

deadmpx 12th Nov 2008 8:01 am
Re: DEAD PLAYER RECOVERY GUIDE
 
This fixed me right up. However my mp4 player is basically only a flash drive. I get no display from the 1.8 inch LCD and it shows no signs of life at all, but when plugged into USB port and turned on, it is a 2GB flash drive.

Quote:
Originally Posted by MP4killer";p=&quot (Post 32735)
I too had the dreaded adfuupdate.inf error- "this file does not contain information about your device/hardware" with Win XP. I haven't seen this fix on this forum and I saw this on the S1mp3.org forum, and it worked for me- I opened up the adfuupdate.inf file in notepad and cut and pasted in these extra strings where KaiT said to put them (his english is a little off but his/her coding ROCKS! I have no idea how he/she figured this out):


Quote:
kai-t Joined: 26 Jan 2007 Posts: 6
PostPosted: Thu Jun 14, 2007 5:45 am Post subject: ADFU ADFUUpdate.inf Reply with quote
Hi,

as i tried to recover my MP4 Player after i flashed a wrong firmware, i can't get hin to be detectet as ADFU Device. Even going through the dead recovery guides.
after trying a hole day i recognized that the Problem isn't that the player is not in ADFU mode. The Problem is that the Player has a other Hardwarename.
So you can edit ADFUUpdate.inf to match your Player.

For mine Player, a ATJ2091N with Board: B828 V6 i had to add 2 lines.
One at the beginning after [Upgrade] i added
%USB\VID_10D6&PID_ff66.DeviceDesc%=MDisk.install,U SB\VID_10D6&PID_ff66

And one at the End of the file, in the [Strings] section:
USB\VID_10D6&PID_ff66.DeviceDesc="USB 2.0 (HS) ADFU Device"

After that the Player gets recognized when installing the Driver.

rllanes2004 18th Nov 2008 12:42 pm
i cant get my player display in explorer...what to do...keep trying the guide process???.... i have the ADFU detected and all but not shows in explorer

epl2000 11th Dec 2008 7:30 pm
Hi, Everyone,
I need help,
I just made my Ipod Nano 3rd Gen Copy a DEAD PLAYER,

this is the firmware
QSB13_44T
2007-12-16
9.1.52
2005-01-09

this is the plate number:
SAMSUN 846,
K9G8G08U0B,
PCB0,


my plan is to backup firmware from my other ALIVE Player,
and restore it to DEAD player.

i tried to use S1FW, no luck.

anyone please help

thanks..

epl2000 11th Dec 2008 8:05 pm
i tried this fw
no luck

Chip AK1025 Board G 18A MAIN v0.3 Screen LDF TT-1807_1211_IPODM.fw

ah, ok im doing s1clone,

is the mp4 suppose to have blank screen while cloning firmware?

teerak2uk 12th Dec 2008 5:32 pm
Re: DEAD PLAYER RECOVERY GUIDE
 
Hi Guys
i have an 8Gb Nano 3g which is stuck on the hour glass but cant seem to find the correct firmware for it details i have are below

regards

hynix
hy27uu08ag5m
tpc8
751amtuj7019mq

screen XY-1.8TBN-KMA

rodogg 13th Dec 2008 12:01 pm
Re: DEAD PLAYER RECOVERY GUIDE
 
hello guys,

i have a similar problem. i have a 3rd generation ipod nano clone (that looks like this one http://cgi.ebay.com/ws/eBayISAPI.dll...ayphotohosting)

it has 2 gig memory and a 1.8 inch screen. on the back cover is a name iWAVE. i cant seem to find a board id but it only has 1 screw on the back (lower back) covered by a small sticker. when opened, i see a chip marked AK1025.

previously, when you turn it on the screen would hang at the hour glass and it would not be recognized by the computer when connected. i attempted the "recover dead mp3 player" guide and used a AK1025 firmware i downloaded from this site. the player reads on the computer now as a flash drive but i cant get the screen to turn on. i can create the usual folders but cant get the screen to light up. its completely black.

anyone know how to resolve this?

delph2009 16th Dec 2008 11:01 am
hhi
ihave sony mp4
i need frimware :
AK1025
8ED20AB0F5

astina76 16th Dec 2008 11:22 am
I have dead one MP4 player, Its recovered to AFDU device, but I don't have an updated firmware files.
So, I need that FW..
does anyone can help me..?

Board ID: BKS25056_MV6A No:071116

LCD ID : FPC888100C_V0.0

Memory Chip: hynix HY27UU08AG5A

CPU ID: AK1025

Thanks...

rodogg 16th Dec 2008 4:54 pm
anyone know where i can find the firmware for this board

**QS91B13 V0.4**
**2008*02*28**

lolita 16th Dec 2008 8:44 pm
Re: DEAD PLAYER RECOVERY GUIDE
 
For the one with the BKS25056:
http://www.s1fw.com/Firmware-1/BKS25...N--en-bin.html
http://www.s1fw.com/Actions-AK102X/A...8V-DN--en.html

For the one with the QS91B13:
http://www.s1fw.com/plus/search.php?...e=titlekeyword

rodogg 17th Dec 2008 3:30 am
Quote:
Originally Posted by lolita";p=&quot (Post 55088)
hey lolita, none of the QS91B13 work

ryu_e 21st Dec 2008 10:09 pm
AdfuUpdate.inf DOWNLOAD
 
You can download AdfuUpdater.inf from this site:

http://www.machspeed.com/drvrs/Firmware%20Updater/MP3Driver/?S=A

macinesa 24th Dec 2008 7:54 pm
Help please
 
Hello,
I cannot fix the mp4 digital player
I have a blue screen and the mp4 is not detected by pc.
This is the mp4 foto:
http://www.digitexpert.net/ds/img/products/mp3-a4/4.jpg

The information I have found with chipgenius software:

PnP Device ID: VID = 10D6 PID = FF66
Serial Number: 5&&93A2790&&0&&6
Revision: (Information not returned)

Device Type: Standard USB device - USB2.0 High-Speed

Chip Vendor: Actions
Chip Part-Number: AK1011

Product Vendor: (N/A)
Product Model: Recovery

Please someone can send me the full firmware because I dont have the backup.
Thank you.

dustin in kentucky 28th Dec 2008 3:50 am
i cannot find the file AdfuUpdate.inf in WINDOWS. it simply says file not found.

dustin in kentucky 28th Dec 2008 4:02 am
now i'm getting "specified location does not contain information about your hardware"

AnthraX 3rd Jan 2009 5:43 pm
Re: DEAD PLAYER RECOVERY GUIDE
 
Dude ...you're the best on earth i owe you 10 beers :D

szakylinux 13th Jan 2009 12:50 am
Hy ...

I have a litel problem whit my mp4 ..i tryd to update the frimware and now a have a white screen , but under the white screen it`s working .. WHAT TO DOO

Olijf 16th Jan 2009 9:14 am
Re: DEAD PLAYER RECOVERY GUIDE
 
It is not working for me only the part of making it to an ADFU device.
It says: Downloading the restorable main Program and don't continue.
If I disconnect the device it says: Downloading The Boot record.

panapok 19th Jan 2009 5:09 am
Quote:
Originally Posted by Pocket_Nano
First I would like to say thank you for the help tadad1 you are a life saver. This morning I started to do what you said. I ignored the windows logo error but then after setting properties to ignore the windows logo error windows automatically installed the driver I didnt have to do any steps in the guide. But now when I get to the last step to load the new firmware it sometimes says device not detected when opening the mp3 utilities so I turn off the player and turn it back on again and open the update utilities again then it says - device switching failed, reconnect device please!-. But now there is life as I get the blank blue screen while its plugged to the computer which it was not doing that before. So we are getting there I think. Thanks!
hi...i'm just a newbie here...
pls provide me the correct of my palyer..

CM60009-501
2006/09/07
ACT_V3.5.35

Plate No. CYTY-963C
Screen No. CM60009ACT6

pls email me--

thanks

tiaret 23rd Jan 2009 1:31 am
Re: DEAD PLAYER RECOVERY GUIDE
 
I have a dead player (with fm radio); I look for help to get it firmware.
Board ID: Bks7513008-v1 070129
Large chip(Nand Flash Memory chips): Hy 27uf082 g2a
Small chip: ACU7513
Code in the side of Screen: Dfm-081a 142027-2
berroubaaek@yahoo.fr
Thanks.

Olijf 23rd Jan 2009 5:53 am
Re: DEAD PLAYER RECOVERY GUIDE
 
It is not working for me only the part of making it to an ADFU device.
It says: Downloading the restorable main Program and don't continue.
If I disconnect the device it says: Downloading The Boot record.

Serzhl0o 28th Jan 2009 12:03 pm
Quote:
Originally Posted by tadad1";p=&quot (Post 4807)
wexku, You may have to repeat the process more than once. You may also need to try one of the other full version firmware and format your player.
How to do a format mp3 flash if windows show 0 mb and windows write can't format?
http://img145.imageshack.us/img145/3976/52259117pk1.png
AK1025 8H021AB
VID = 10D6 PID = FF66
mont: xy-1.8cc v2
memory: hy27uu08ag5m
plata: BSK25002kv11

Marco16 19th Feb 2009 4:37 pm
where i can download the adfu driver?

Groovy 28th Feb 2009 7:25 am
you have it your computer in windows ffolder...

artan 1st Mar 2009 2:41 am
HELP ME !!

[img=right:77aa267b69]http://www.xxlimg.com/images/3umj5xxfl2fx8s67t3nv.bmp[/img:77aa267b69]
[img=right:77aa267b69]http://www.xxlimg.com/images/v4lc6acrv80fssplz6a9.bmp[/img:77aa267b69]
[img=right:77aa267b69]http://www.xxlimg.com/images/bp00s1362dwvqgnf85.bmp[/img:77aa267b69]
[img=right:77aa267b69]http://www.xxlimg.com/images/r0mv7w2kfxas1o6dmp.bmp[/img:77aa267b69]
[img=right:77aa267b69]http://www.xxlimg.com/images/dvmqgeq2q6ikhjg1rx1q.bmp[/img:77aa267b69]
[img=right:77aa267b69]http://www.xxlimg.com/images/zhgs2pd3c5dx5m57k5xs.bmp[/img:77aa267b69]
[img=right:77aa267b69]http://www.xxlimg.com/images/oyc9f61a2x0ugfp3da30.bmp[/img:77aa267b69]
[img=right:77aa267b69]http://www.xxlimg.com/images/lrb7oclqczdttdg93c6.bmp[/img:77aa267b69]
[img=right:77aa267b69]http://www.xxlimg.com/images/blxt8bxm45mi982cgfw.bmp[/img:77aa267b69]

kloun2 2nd Mar 2009 12:51 am
Re: DEAD PLAYER RECOVERY GUIDE
 
ok i have done it all, and my mp3 player showes blue screen with sandglass and nothing else. also my computer cant reconize it right now.
so what i should do?

Jupya 3rd Mar 2009 7:53 am
Re: DEAD PLAYER RECOVERY GUIDE
 
artan do this:delete the thing in red circle( ; ) and add thing in blue ( { )[img]http://img124.imageshack.us/img124/7607/93186651.th.png[/img]

rodg1984 12th Mar 2009 4:33 pm
Allright I've done enough searching and reading I think my head is about to explode.

I've got two of the Ipod Nano clones (Lisong Mp3 Player Wilson Co. Ltd. 9.1.52) that I had tried upgrading the firmware on. Through my reading I have learned that that wasn't the best idea.

Here's the information I got after opening it up, if any other information is needed to help me out, let me know and I'll open'em back up. Not sure which numbers mean what.

HYNIX HY27UU08AG5A
AK1025 K0129H2V2M
UUT 080311

Anyways I have found a firmware that lets the players turn on, the screen is sideways and it gets a disk error except on FM Radio, Setup, and Tel-Book. The current firmware is, LSD_91N18V_A1 2007-09-05 9.1.52 2005-01-09. Original is, LSD_91N18H_A2 2008-04-05 9.1.52 2005-01-09. If anyone has the original fw, an upgrade, or just any insight as to what to try next, I'd greatly appreciate help.


Thanks In Advance,
Rodney

ediko 23rd Mar 2009 1:05 pm
Re: DEAD PLAYER RECOVERY GUIDE
 
Please anyone help me. I cant get past the damn device managing. I tried everything. I downloaded different ADFUUpdate's changed them myself, downloaded mp3 tools connected disconnected etc in all ports. It still an unknown device. When i try to update the driver to the ADFupdates it writes it has no information or its not vista x64 compatible. BTW the usb adfuud device driver isn't there too. already spent all night on this. I just cant get it to work. :evil:

lolita 29th Mar 2009 6:53 pm
Quote:
Originally Posted by rodg1984";p=&quot (Post 58754)
Allright I've done enough searching and reading I think my head is about to explode.

I've got two of the Ipod Nano clones (Lisong Mp3 Player Wilson Co. Ltd. 9.1.52) that I had tried upgrading the firmware on. Through my reading I have learned that that wasn't the best idea.

Here's the information I got after opening it up, if any other information is needed to help me out, let me know and I'll open'em back up. Not sure which numbers mean what.

HYNIX HY27UU08AG5A
AK1025 K0129H2V2M
UUT 080311

Anyways I have found a firmware that lets the players turn on, the screen is sideways and it gets a disk error except on FM Radio, Setup, and Tel-Book. The current firmware is, LSD_91N18V_A1 2007-09-05 9.1.52 2005-01-09. Original is, LSD_91N18H_A2 2008-04-05 9.1.52 2005-01-09. If anyone has the original fw, an upgrade, or just any insight as to what to try next, I'd greatly appreciate help.


Thanks In Advance,
Rodney
Format the device. As for sideways display, unless you cannot use the device and are willing to try more firmware leave it.

ediko 30th Mar 2009 6:30 am
Anyone knows a program or something for my problem?

mr.inter 31st Mar 2009 10:54 am
Re: DEAD PLAYER RECOVERY GUIDE
 
My Ipod Nano Clone 1.5 inch screen & 2GB memory does not even turn on and is not detected by the computer. What can I do please? Thanks.

indigovox 31st Mar 2009 10:16 pm
Re: DEAD PLAYER RECOVERY GUIDE
 
Please, I need the firmware to my MP4 device.
Chip ATJ2092N.
I used some I found here, but I have not succeeded,
not working to my MP4.
Please, Somebody help me. :cry:

djalismail 12th Apr 2009 12:42 pm
hey brothers is there any firmware for my mp4
AK1025 samsung 846
k9g8g08u0b
8h024ab

Commune 15th Apr 2009 4:12 am
Pbm in reviving mp3
 
Hi,
Thanks for helping.
I am trying to recover player. It is detected as USB Device. So I followed the red part of the guide.
I can find AdufUpdate.inf, but not select it: windows tells me that nothing is found in it for this device.
Wait for your help.

lnzcp 17th Apr 2009 1:09 am
thanks it works
but now I donŽt find the correct firmware for my mp3-player - the firmware from the cd doesnŽt work.

here IŽll send you the numbers on my mp3 player
AK1025
HY27UU08AG5A

who can tell me where I can find the correct firmware.
thank a lot

Nerijus 19th Apr 2009 3:12 am
http://img15.imageshack.us/img15/5561/ipodclone1.jpg
http://img24.imageshack.us/img24/898/ipodclone2.jpg

Please help me to find firmware for this chinese ipod clone (2 GB with FM):


Main processor
AK1025

Display
DW018-13
SNW LCM

Memory
Samsung K9GAG08U0M (2 GB)

MainBoard
HAIYU
M681-v3

Tuner
SPT SP3767

I'm totally lost :cry:


All times are GMT -7. The time now is 5:52 pm.
Page 26 of 28 « First 16232425 26 2728
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO 3.6.0 RC 2