Re: DEAD PLAYER RECOVERY GUIDE
 

Please, I need the firmware to my MP4 device. clone ipod 8gb with real 1 gb
Chip ATJ2092I and Hinix HY27UF081G2A board DX510310-V2
I used some I found here, but I have not succeeded,
.
Please help me

Re: DEAD PLAYER RECOVERY GUIDE
 

ok, here is the deal, i make it all until the adfuUpdate, windows shows me up an error "the folder you specified doesn't contain a compatible software driver fpr ypur device. If the folder contains a drever, make sure it is designed to work with windows for x64 based systems", what can I do?

Re: DEAD PLAYER RECOVERY GUIDE
 

My Ipod Nano Clone 1.8 inch screen & 2GB memory does not even turn on. What can I do please? Thanks. The computer detect 2 drivers when i swich my player. Which driver i can take Actions USB 2.0 (HS) WinUSB Device or S1MP3 ADFU Device?

http://lh5.ggpht.com/_Ms-Apy47Sh4/Sf...0/IMG_1057.JPG

http://lh6.ggpht.com/_Ms-Apy47Sh4/Sf...0/IMG_1058.JPG

http://lh6.ggpht.com/_Ms-Apy47Sh4/Sf...0/IMG_1054.JPG

http://lh3.ggpht.com/_Ms-Apy47Sh4/Sf...0/IMG_1056.JPG

Please help me!

Re: DEAD PLAYER RECOVERY GUIDE
 

In my opinion You should choose Actions USB 2.0 (HS)

Re: DEAD PLAYER RECOVERY GUIDE
 

And whit Actions USB 2.0 (HS) the Player don't work, not turn on!

Re: DEAD PLAYER RECOVERY GUIDE
 

That's because You must to find suitable firmware and with MP3 player upgrade tool to upload it.

Re: DEAD PLAYER RECOVERY GUIDE
 

Tnahks Nerijus !
Would you tell me which firmware and with MP3 player upgrade tool to upload for this model ????

Re: DEAD PLAYER RECOVERY GUIDE
 

yos dude I need pay you a beer :D

Re: DEAD PLAYER RECOVERY GUIDE
 

Hello! I have this JOY 888 (copy of newman K8player Anykaa AK3221mb, 2 GB, 2MP camera chip ,wich is dead...
BOARD: KGMP888-GAME-AK-V3(covered by the SD card slot)


When i try to start it it shows "Loading...." and that way it stays untill i press reset. No USB conectivity!

When i enter bios by pressing and holding power button for 10 sec, it enters a blue screen writing :"BIOS KG888-5.3.2-LinDa-F Please Press Reset!".

Pressing any button on the device in the BIOS state makes "Please press reset" text blink, after 4 buttons pressed(random) it doesn't blink any more.Could it be a button combination for the device to enter firmware upgrade state?Does anybody know how to rewrite firmware on thes device? It has no USB conectivity at all and the bios menu does not promt me for formating or anything else. !Please Help , Thanks!

Re: DEAD PLAYER RECOVERY GUIDE
 

http://farm4.static.flickr.com/3632/...0671617f62.jpg

http://farm4.static.flickr.com/3652/...5bbf01e8dc.jpg

Hi every body.
I don't find my firmware, i have a clone ipod nano 3rd generation
CPU: AK1025
and the second constituant is:
hynyx hy27uu08ag5a
If someone can help me it's wonderful thanks for advanced

I have a MP4 player just like this one, only it's 2GB
On it's processor is written: ACU7513 and 02144CA?C3C
On the memory: SAMSUNG713 and K9LAG0?U0M and PLB0
( The "?" are the letters where i cannot read what letter or number is there. )
I would be very great full if someone can point me out to a framework that could work on my MP4 player.
Thank you in advance!

EDIT: The last version that worked on it was 9.0.50 or 9.1.50... can't really remember

Player: Novex NFP-2003
Payment: B896V2
The processor: AK1025
Memory: Samsung K9LAG08
The display: KLM 167E01-1A

Need FW

i have zebronics mp4 player 1gb. it's version no is 9.1.52 and firmware no is "080926 MUPIC B635_N4xb_V3.0_97N". after repeating 4 times the process for firmware upgrading this is not working yeat. althouth every step completed sucessfully and as accepted but still player gets dead again and again.pl help me.

Sunplus - stuck at startup screen
 

i followed the guide, i have an AJ250_v14 pmp player
the power led was ON, but it won't go to boot, before i tried guide the screen always goes for loading all the time, after i try it the screen just dead won't display anything only the led power was ON,please help me

Hello!
I need a firmware for an mp3/mp4 player Majestic 1 GB IC 11/1G

XA FPC888083A-V0.0

Control: ak1025 7j054ab 0k1
Plate No.: 91c066 07/07/23
Screen No.: DFM-0838-NL-WD.GLAFJ01

0746 29f8g08maa

Latest version on device was 9.1.52.

Device firmware information
Device name: S1 MP3 PLAYER
Productor: Wilson Co. Ltd.
Version: 9.1.52

Thank you in advance!

How detect mini mp3 player
 

my mini mp3 player working fine but sudenly power down .Now not detected by pc only show driver name and not show memory in pc and light is not showing when power on .Plz help how detect and update firmware

Problem Not Solv
 

Mr Admin What You Say I do..But My Ipod Light Go Out ..Now What I Do..

My Email ..Rakib.1111@yahoo.com

Please Help Me..

Please create a new thread for your problem. You will need to open up your player and post information such as board and plate ID.

Can someone help me with a firmware for my MP4 PLAYER ???
 

I need a firmware for an mp3/mp4 player Majestic 1 GB IC 11/1G

XA FPC888083A-V0.0

Control: ak1025 7j054ab 0k1
Plate No.: 91c066 07/07/23
Screen No.: DFM-0838-NL-WD.GLAFJ01

0746 29f8g08maa

Latest version on device was 9.1.52.

Device firmware information
Device name: S1 MP3 PLAYER
Productor: Wilson Co. Ltd.
Version: 9.1.52

Thank you in advance! :(

death mp3 player
 

I need firmware for: Xwave s-42 1gb (PIC)

AK1025
7L039AB 2LJ

hynix KOR
HY27UTO88GM
TPCB 814H

board:
MP-1052Q-TSLSR(KEY) V2.1
070713 LIANG

When it first broke down, screen showed only hourglass, and xp couldn't detect it. Yesterday I gave it the last try, and managed to install some random usb driver for it. Tried some firmwares but now I only get white screen instead of hourglass...

i neeeeeeeed dha firmware in my sig plzz

Hi, I am faced Problem with My JXD921 PMP. I recently Purchased. I Burned Direct Aimg , Bimg and firmware. to my device. Once Succefull installed I reset and restarted. I can Figure only Green Light on the player not LCD Light or Glow only total Blank screen. I think the Firmware install it not right.
So I tried Using again FRM but FRM unable to detect any device. whearas as soon i connect on System my computer shows 2 removable drives one 1 GB (internal Flash memory) an other 2 GB my SD flash Kingston card.
I have a secure backup of my Orignal firmware. But unable to put it back. drivers of my PMP is SPCA5000 all things are prefect but I would like to know the way to boot my Device and detect it to FRM there after i can re burn my old Firmware which works. So please help me.
On internet I have heard if such problem occurs due to wrong firmware either we need to open and short circut an IC pin. or We need to please combination of Secret Button to detect the device to System than open FRM and load the Firmware.
PLease Help me.
I have down below provide a document of my dignose what helpd and how with screenshots.
RapidShare: 1-CLICK Web hosting - Easy Filehosting

Hello!
After an unsuccessful firmware player ceased to run, the computer does not recognize it, that's data that is on the board and chips:
Lisong MP3 Player

HYNIX KOR
HY27UT088G2M TPCB 739A
ACU7503
g2079ca c20
SP3767AHN SPT 07CS31
JBE11 V10 2007/07/03

Need more likely a complete firmware (if you can tell how to do, because it probyval sew as ADFU device, but MP3 Player Firmware Update not responding)

P.S. Sorry for my English

hey,
i send some pictures to my mp4 player and the next moment i finished the sending it started to flash,i turned off and waited for 5 min but nothing, now it looks like dead
the player is compacto mp4 digital player on the batterie has a number: FS6003/2GB060809121

Hi
I have a Marshal player. Model ME-F08. Heres its pic n details: Marshal ME-F08
http://www.marshalusa.com/Image/ME-F08.jpg
My player plays musix. But my problem is with its LCD Screen! The LCD doesnt start most of the time. I mean the player turns on n works, but display shows nothing! And sometimes I turn the player on, display works for a while and after a few seconds (or a few minutes) display goes off :(

anyone can help me?
what should i do?

Can't move on
 

Hello, fellas, so here's my deal:
Player Specs: I have an ipod nano clone:


Large Chip: hynix KOR HY27UU08AG5A TPCB 902H
Mid Chip: AK1025 81003AB 21B
Little Chip: Colment CL6010 M1 2008

Issue:
Okidoki,so I'm gonna tell you delay by delay ¬¬, so that you can help me better:
With this guide I get to the part where is needed to get the ADFU device thingy, so I tweezer-it, get there and choose the "don't search option" and click next, but when clicking next I'm not getting the "show all devices" part; it takes me right to the "select driver" one, then at that part the option it delivers me is "USB 2.0 (HS) ADFU Device", click on Have Disk, search for ADFUUPDATE.INF, but mine is "AdfuUd.sys" and it is in system32/drivers (don't know if that affects in some way), later the USB 2.0 (HS) ADFU Device is installed, but here's my problem: I can't enter it on My Computer nor using RDiskUpdate from MP3Utilities, can't enter it from anywhere and the properties tell me that it's working fine, hence I don't know what to do next.

Question:
Any advice, mate? Can't get past there, I'm totally stuck.

Hello i need help. i did what is said in recovery guide. when i short the pins and select afudupdate.inf it installs as Actions USB 2.0(HS)WinUSB Device, not AFUD DEVICE. any helpp plzz??

Can't find the right firmware
 

Hi fellas...
I have a Chinese Sony MP4 player (the picture is attached)

http://mympx.org/forum/attachment.ph...1&d=1269762850

Its a SUNPLUS MP3052A-HL171 M175Q030731

The problem is that I'm unable to find the right firmware for it...

Please help http://mympx.org/forum/attachment.ph...1&d=1269762850:(

evilpro

Can you create a seperate post instead?
In the subject, put the firmware information. This will help with the searches and if people find a compatible firmware, will post a reply to you.

Thanks a lot for Ur suggestion, Sir...

Got the drivers for the usb device installed but windows isn't picking it up in my computer or disk management? how can i format?

Very often the USB leads supplied are faulty. I had a ipod lead and a mini USB lead supplied for 2 players both faulty. Replace with better quality ones cured player/upload problems etc.

ian

I have an ms 408 gloss:


Chip: hynix KOR HY27UU08AG5A TPCB 821F

i can not find firmware :(

Hi kocko

I guess the HY27UU08AG5 is a 2GB Hynix flash chip. You will need a lot more information to find the firmware. Like numbers of controller chip and display device. Also if you could post the picture of your player so that people with a similar one can see... and share their firmware with you.

hope this will help........

MS 408 gloss
It is HY27UU08AG5 TPCB 821F a 2GB Hynix flash chip.
display tipe: 1.66" tft
display resolution 160x128

can this help,to find firmware?

kocko ... just lift the battery and you would see another chip (second largest on board), this would be the micro-controller (master). Also on the side of the LCD would be some numbers written, post these two part numbers and see we could locate a suitable firmware for your device.

yes ... the largest chip is the flash memory and in your case it is a 2GB ... How much was stated on your player ??

I lifted the battery,but there was nothing there.i found master chip on anoter side.

ALI dri
m5661e b1
d737 tg05
x719124000ga

:)

but there are no numbers writen on the side of the lcd :(