[solved] Looking for firmware ATJ2051H

Groovy · #1 (**permalink**) 22nd Oct 2006, 12:37 pm

Hey guys pls help me... I ve got 2 days old 4GB Mp4 and I fu*ked it up...
I have no backups.... :cry:

I ve read those manuals how to recover it...
I did it excactly as you said but at the end ehdn I upload there a new full firmware it does nothing and when I turn it again it sais again that I ve no firmware...
I guess I have bad firmware...

So I have here some photos... if someone have the same or know what it is for a type pls write me...
I ssearched for that number inside but there is no number on that board :shock: :shock: :x :x

pls help me out....

admin · #2 (**permalink**) 22nd Oct 2006, 1:29 pm

Groovy

Does your player get detected by Windows as a drive?

Also, what firmware have you tried? If your player is in recovery mode, it's best you use a full firmware. You can find a lot of full firmwares from the "Downloads" --> "firmware" --> "Full Firmware" section. Unfortunately as you don't have a backup, you will have to keep trying until you find a firmware that is compatible with your player.

tadad1 · #3 (**permalink**) 22nd Oct 2006, 4:56 pm

Groovy, If when you start the upgrade utility you get a message that your player is in recovery mode you need to use a full version firmware, it most likely will not recover your player but it will prepare it so that you can then try backups or dump.bin files.
Then you just need to go through and try all the firmware you can find until you find one that suites your player.
If your player stops being recognised then you need to follow the Dead Player recovery Guide to do a hard reset, load a full version firmware again then continue trying dumps.

Just looking at your photo's your hacked player is really only a 2GB, the memory chip K9WAG08U1A (16GigaBit) = 2GB.

Groovy · #4 (**permalink**) 22nd Oct 2006, 9:42 pm

Hah But I put there 4GB

:arrow: I tried all your full firmware and it does make the same all the time...
Noe thw windows do not recognise the player so I will follow the manual again...

tadad1 · #5 (**permalink**) 22nd Oct 2006, 10:30 pm

Groovy, After you load a full firmware are you able to load dump files?

Groovy · #6 (**permalink**) 23rd Oct 2006, 7:11 am

Quote:

Originally Posted by tadad1";p=&quot

Groovy, After you load a full firmware are you able to load dump files?

No I said... If I turn on that prograam agaion it says recovery mode again

Groovy · #7 (**permalink**) 23rd Oct 2006, 7:28 am

I cannot iinstall the full firm,... dunno why

After I made the conection between pins it makes - b--bi and it is that -adfu device... I am tring to put there all full firmwares I found but if I upload it... it makes the same... and aain recovery mode and sometimes it writes - Device wasn t recognised and I have to open it again and it wirks then...

Groovy · #8 (**permalink**) 23rd Oct 2006, 10:35 am

HEY I found that ID number

) so I downloaded that firm... it is : ATJ2051H

But still if I run it it is recovery and if i open any firmware it writes version 3.2.21 or smthng like that and producer : Wilson... it does it for all the Firmwares... Shit happens

coisty · #9 (**permalink**) 23rd Oct 2006, 12:02 pm

Hi Groovy

been looking for same firmware check out my thread titled Firmware for NANO clone ATJ2051, samsung 634 2gb

If you find firmware that works please let me know

I think more and more members will be looking for the same firmware as this guy is selling about 30 of these a day on EBAY

Coisty

Groovy · #10 (**permalink**) 23rd Oct 2006, 12:23 pm

I found some... there are many of them on s1. http://www.s1mp3.org/en/downloads_fw.php

but I have bigger problem with that I worte last time... any1 knows pls ?