HERE, FW full 9.1.51
 

Hi everybody,
in this url there's a full fw S1 mp3 player Wilson Co. Ltd 9.1.51

"http://www.exoticsa.com/2007/descargas/DIGIPOD%20SD-18N%20%20(1G%20,%202G%20,4G).rar" (copy and paste)

i hope that people with dead mp4 can use this fw

good luck

German

Thanks for sharing this gemelo71.

Is this with a .bin or .fw extension?
Do you have any other information about this? I'll upload it to the Downloads section.

Have you used this yourself?

Re: HERE, FW full 9.1.51
 

hi,
your welcome. with .fw extension. i hope somebody can use it

Re: HERE, FW full 9.1.51
 

which I use loader this file ????? :roll:

Hi
This put my half dead Glacier clone into ADFU mode, but firmware was recognised as 9.1.51 by the upgrade tool. No harm done, just not right for my player! Please anyone with any 9. series firmware (ideally for Glaciers or other 2 inch screen players) can you upload? The more firmware we have to try, the more players will be saved!

Re: HERE, FW full 9.1.51
 

Im am using MP3 Player utility 1.48.

When I try to us the download file the utility does not even see the firmware. When I change the name of the firmware to include a .fw ending the utility see the firmware but them call give it an " invalid upgrade" warning.

Any suggestions?

try upgrading your mp3 utility
use 4.15. you will have to add .fw so it recognisees it but I was able to use it
my mp4 is still dead though

Re: HERE, FW full 9.1.51
 

I have 4 identical chIpod shuffles which I purchased in China.

When a went to use the devices I kill two of them when I fully loaded the supposedly 4G player. It was then I figured out that I actually had 1G player. I followed the How to fix hacked chIpod instructions and fixed the remaining two machines to run as 1G player.


I then when about trying to recover the Dead chipods. Following the instructions and postings on this board, I have set the player into ADUF rescue mode. Now I need to load a full firmware version.

Going to http://www.exoticsa.com/2007/

I downloaded the 4.15 tool and used it to look at the firmware version on my working chipods: Bother were Wilson Co LTD version 9.1.51 firmware.

Then from the same site, I downloaded DIGIPOD SD-18N and uncompressed the firmware. At this time I added an .fw extension so that the MP3 utility can recognize the file.

When I open the file using the 4.15 MP3 utility the SD-18N.fw file is recognized as Wilson Co LTD version 9.1.51. When I hook my Player in ADUF mode in to the USB port the MP3 utility recognizes the player and said it is ready of upgrade. I tell it to upgrade the firmware and the utility
upgrades to player and indicates that the firmware installation was successful.

At this point the ADUF device disappears from the USB items listed under the Hardware Device Manager.

This is where my troubles start! I can not find the player anywhere on the PC. It is not recognized as a flash drive or a hard disk. It is nowhere to be found.

I then turn off the player and remove it from the USB port. I wait a couple of minutes and then reboot the player and wait a few more minutes so that it has had more than enough time to boot.

When I plug the play back into my computers USB port. Win XP Pro makes a sound like it just noticed a new USB device, but I can not find the device anywhere in the Device Manager or Using Windows Explorer.

The MP3 utility or MP3 disk format programs do not recognize the player either.

I have read one post that said I may have to format the MP3 drive from windows, but I have no idea how to do that being I can not find the device on the system.


Please Help!

Re: HERE, FW full 9.1.51
 

top de linha.. agora nao sei como baixar..