mohyom i think u r having same ipod as i do so u can too help me moreover u r my neighbourhood brother so plz tell me how to enter bios andwhich firmware will work in my ipod .sableroku has told earlier to somebody how to enter bios , but he has written in portugese language which i dont know so plz help me buddy

Sak-cheegi i downloaded your file but i cant find the pass word i tried everything. plaese help

Re: MP4 Players ANYKA chip **RE-UPDATED **
 

just scroll down and you will see that it says download not upload!!

Re: MP4 Players ANYKA chip **RE-UPDATED **
 

RAMANDEEP SINGH
dear follow this
and how to format check 1st page in this topic
best of luck

how to transer a new firmware to he mp4 player?????
& ya how to install themes & games in the player........

Re: MP4 Players ANYKA chip **RE-UPDATED **
 

HELLO FRIEND

dear howto transfer firmware check this topic 1st page ok

best of luck :)

Re: MP4 Players ANYKA chip **RE-UPDATED **
 

hello friends

i have some mp3 players like wilson.co

i connect the pc found new hardware usb device but no Adfu Update.inf driver compatible how to move mp3 player in recovry mode
plz help this problam i need a driver urgent :?

I have the following numbers from the Anyka chip of my dead MP3 player:

AK3221MB24405
FA0657

I have followed the procedures in this thread, but when I restart the player, it only loads the software 3/4 ways, then it freezes and has to be reset. I have tried MP5 and firmware_anyka with the same results.

The only step I was unsure of is after I safely remove the USB hardware via Windows, my player says "Software Loading". I cannot restart the player without resetting it. Or, I can restart it if I unplug the USB cord, then I have to press the power button 3-4 times for it to start up. Should I be restarting it before unplugging it/disconnecting it from USB? Or what? Thanks for any help!

i re-formated my player and it shows usb disk and computer detects "ANYKA USB NAND OPN ZONE USB", THEN I COPY THE FIRMWARE GIVEN BY U (MOHYOM) TO 16 MB AND RESTARTED MY PLAYER BUT IT LOAD UP TO 3/4TH PART AND THEN GOT HANGED THERE. I COPY AKRES.BIN , MAGIC.BIN IN THE REMOVABLE DISK OF 16 MB. ONE TING I M NOT SURE IS THAT THE FILES U HAVE GIVEN ARE BIN FILES AND I DONT KNOW HOW TO OPEN THEM BUT I COPY THEM IN 16 MB DISK. AKRES.BIN AND MAGIC .BIN ARE LOCKED FILES I THINK U CAN UNDERSTAND BUT I COPIED THEM WITHOUT OPENING THEM , NOW HOW THE PLAYER IS ABLE TO LOAD THEM IF THE FILES ARE LOCKED .PLZ TELL ME HOW TO OPEN .BIN FILES AND IS IT NECESSARY TO OPEN THEM OR THAT IS NOT A PROBLEM.IF WE HAVE TO OPEN THESE FILES THEN COPY THEM TO DISK THEN PLZ TELL ME HOW TO OPEN THESE FILES AND WHAT SOFTWARE I REQUIRE TO OPEN THESE FILES.

I M VERY DEPRESSED BCAUSE I WANNA FIX THIS PROBLEM AND ANYONE HELPING ME ......... WOULD FULLFILL MY JOB

Re: MP4 Players ANYKA chip **RE-UPDATED **
 

You do not need to open the files. These files are for the operating system on the MP4 player and although you cannot undestand them, your player will. Just do as you already have, load them onto the 16mb portion of your player. If you are lucky, it will work. I have a similar player and after trying 6 different sets of firmware files, the player will still not work. Green light comes on when switched on and goes off when any key is pressed. Can still get to format and usb disk screens and load firmware, but no firmware works so far. Hope you have more luck than me.
happy Crimble