IPOD Nano copy 8GB, firmware Chip Hynix HY27UF081G2A

[zerio]

Originally Posted by lolita";p=&quot

What is the screen resolution?

Actions supplies a solution with ATJ2091x and 128x32 mono LCD.

Its a COLOUR LCD and I guess its 128x32.. Screen is sorta installed upward , the longest lenghtiis up and down notlefttopright( can youunderstand me?) Please help me..xiexieNI

[zerio]

Originally Posted by lattesurf";p=&quot

you'll need to perform the Dead Player Recovery Guide here http://www.mympxplayer.org/dead-play...ide-vt567.html

Hi lattesurf.. and LIST

First of all the board is ATJ2091N FB181DB196.

My big doubt is how to drag the screwdriver to cause the shortcut...is one screw drive dragging only one side of the chip´s pins and then todo the samething in the other side correct? This is not clear to me. OR, Shall I cause short cut amongst pins from each sideof the CHIP simultaneously?

Please could you clarify the short cut process regarding the shortcut process itself? ....ie shal the shortcut be made with a pin from each side of the chip or I can drag and cause the shortcut from one side of the chip and then the other side of it . The shorcut is caused by draggging pins from each simultaneously or pins fromthe same side cause shortcut either? Thanks indeed.

[lattesurf]

zerio , now i'm confused. If your player is a nano clone, then the screen has got to be at least 1.2" (128x96), 1.5" (128x128), 1.8" (128x160), 2.0" (220x176).

If it's 128x32, then it could only be the monochromatic screens, which the firmwares on this site do not work. You'll need to verify your screen size first. A picture of the actual player would be good.

Regarding the shorting of the pins, it is a trial and error method.
In some cases, you'll probably need to disconnect the battery. This can be done by cutting the wire or de-soldering the wire.
The USB cable would also need to be connected to your computer.
To short the pins, you'll need either a fine tweezer or simply a bent open paper-clip. Short the left and right side of the memory chip, 1 pair at a time.

What actually happens when you on the player or connect the player via USB, is that the player attempts to boot up. But with a wrong firmware installed, it is unable to boot up successfully. So internally, it is constantly "restarting" upto the point where it tries to load the firmware but finds it to be incompatible.

With the player unable to boot up properly, the computer is unable to detect it, which results in the drive not appearing and not being able to flash in any firmware.

So the shorting of the memory chip pins typically causes a read error on it. This would invoke a "restoring" state (i can't really remember, but it's sort of "factory reset"), that allows an installation of the ADFU server.

[zerio]

Hello Lattersurf

Sorrry it was a mistake ,the screen is 1.8" (128x160) according to the ad,pleasecheck my mp3modelhere at:
http://www.dhgate.com/productdisplay...132f51bbc3178a


However believe it or not I had paid for the model shown here http://www.dhgate.com/productdisplay...13244d52bf314b all in al,besides getting an item different than I had paid for , the mp3 is hacked..the website where is listed is no good either..should make the sellerpay full refund but didnt.

BE CAREFUL WITH SUCH SELLER!!!!


So, I must get a little pair of scissors and short each pair composed by each pin from each side , I go and touch the firstleftpin with the firstright pin and so on ..CORRECT? ( sorry for the language barrier...)

I must tell you I cannot desolder the battery..this is impossible for rme..I dont have the apparatus to resolder the battery neither the hand skilll.

Thanks again

Thanks somuch for your help and patience.

[lattesurf]

zerio , regarding the battery, perhaps leave it connected first and try the dead player recovery guide. See if with the battery connected, you are able to reboot the player.

[zerio]

Hi depend on someone to borrow me the tiny screw drivers...toopen the ipod..I forgot to mention that in the lastest mp4brand FOSTONthey have the very same type of images,lay out..dontknwoif it couldhelpe me to get the correct FW but Id thought it was significant to share this info.

Thank you so very much , Il tell you if the battery has blown up oranything as soon as I do that...well..better LOL than tobe pissed and ruin out my days due to such a scammer.

Wish there were otther lists to bring out scammers who sell at other websites...ec21,tradekey,dhgate etcetc..scammer arelike roaches..they seen to be everywehre and to survive any attack.

[lolita]

See my post in DEAD PLAYER RECOVERY GUIDE, with picture show where to short on the pins.

Only short the data lines, anything else can cause damage.

[zerio]

Originally Posted by lolita";p=&quot

See my post in DEAD PLAYER RECOVERY GUIDE, with picture show where to short on the pins.

Only short the data lines, anything else can cause damage.

Hi Lolita
I could only find the moderators posting about DEAD PLAYER RECOVERY GUIDE at
http://www.mympxplayer.org/dead-play...ide-vt567.html

WOuld youplease write the link. Itwould make things much easier?

Im still very confused on how to short,pair by pair each side of the chip,or side by sidepins each side of the chip.. before no clarification ,Id rather go for no short.

xiexieNi

[lolita]

Read "reply" to the message, near the last page.

[zerio]

HiList I was able to short... I could hear the sounds PCproduces when the new hardware is recognzied.,... but despiteof my itemto be recognized as ADFU , inMY Computer I cannotsee any device(masssotrage..usb device or whatverplugged in..) Iguess I needtostartthe marathon to RESTEST all the fws and findout which one fitsbettertomy chinipod.

Regarding Lolita´s lastmessage..thanks..but I guiess Ivealready gotthe short done. xiexieNi